Article

Review Article

Ann Lab Med 2019; 39(1): 15-22

Published online September 13, 2018 https://doi.org/10.3343/alm.2019.39.1.15

Copyright © Korean Society for Laboratory Medicine.

Progress in Automated Urinalysis

Matthijs Oyaert, M.Sc., and Joris Delanghe, M.D. Ph.D.*

Department of Laboratory Medicine, Ghent University Hospital, Ghent, Belgium.

Correspondence to: Corresponding author: Joris Delanghe, M.D. Department of Laboratory Medicine, Ghent University Hospital, C. Heymanslaan10, 9000, Ghent, Belgium. Tel: +32-9-332-29-56, Fax: +32-9-332-49-85, joris.delanghe@ugent.be

Received: March 15, 2018; Revised: April 13, 2018; Accepted: August 29, 2018

This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

New technological advances have paved the way for significant progress in automated urinalysis. Quantitative reading of urinary test strips using reflectometry has become possible, while complementary metal oxide semiconductor (CMOS) technology has enhanced analytical sensitivity and shown promise in microalbuminuria testing. Microscopy-based urine particle analysis has greatly progressed over the past decades, enabling high throughput in clinical laboratories. Urinary flow cytometry is an alternative for automated microscopy, and more thorough analysis of flow cytometric data has enabled rapid differentiation of urinary microorganisms. Integration of dilution parameters (e.g., creatinine, specific gravity, and conductivity) in urine test strip readers and urine particle flow cytometers enables correction for urinary dilution, which improves result interpretation. Automated urinalysis can be used for urinary tract screening and for diagnosing and monitoring a broad variety of nephrological and urological conditions; newer applications show promising results for early detection of urothelial cancer. Concomitantly, the introduction of matrix-assisted laser desorption ionization-time-of-flight mass spectrometry (MALDI-TOF MS) has enabled fast identification of urinary pathogens. Automation and workflow simplification have led to mechanical integration of test strip readers and particle analysis in urinalysis. As the information obtained by urinalysis is complex, the introduction of expert systems may further reduce analytical errors and improve the quality of sediment and test strip analysis. With the introduction of laboratory-on-a-chip approaches and the use of microfluidics, new affordable applications for quantitative urinalysis and readout on cell phones may become available. In this review, we present the main recent developments in automated urinalysis and future perspectives.

Keywords: Automated microscopy, Flow cytometry, Urinalysis, Microfluidics, Test strip analysis, Laboratory on a chip, Urinary tract infections

Urinalysis is a major diagnostic screening test in the clinical laboratory, with an important role in diagnosing and monitoring nephrological and urological conditions. Until recently, microscopic urine sediment analysis was the most widely accepted urinalysis methodology. However, this time-consuming methodology is associated with extensive analytical errors [1]. Over the past 25 years, new automated technologies and informatics have greatly reduced the labor intensity of urinalysis and have created new technical possibilities. This review presents the main recent developments in automated urinalysis and future perspectives.

Microscopic urine sediment analysis remains the key method for urinalysis; unfortunately, the required expertise is not widely available at any time (night time, weekends). Electronic transmission of images (telemedicine) can therefore be very helpful for obtaining diagnostic information [2], enabling consultation with experts regarding unusual or doubtful findings and the circulation of interesting findings throughout the medical and scientific community.

Although dry chemistry technology for urinary test strips has made limited progress, advances in electronic detection have considerably improved the analytical sensitivity of test strip readers over the years [3]. In 2002, Penders et al. [4] demonstrated that automated urine test strip reading enables quantitative analysis for red blood cells (RBCs), white blood cells (WBCs), glucose, and urinary protein. According to the reflectance theory formulated by Kubelka and Munk [5], the reciprocal value of reflectance readings is proportional to the concentration of the measured analyte. Applications of these quantitative test strip readings have been described for ketones [6] and albumin [7].

A classical dye-binding based albumin test strip in combination with a complementary metal oxide semiconductor (CMOS) based strip reader could allow quantitative analysis of albuminuria and the determination of the albumin:creatinine ratio. This development enables obtaining quantitative albumin readings in the microalbuminuria range (20–200 mg/L) [8]. The creatinine-specific test pad allows correction for urinary dilution, which is useful in the assessment of albuminuria [9].

Using CMOS technology, very sensitive readings can also be obtained for leukocyte esterase and peroxidase activity [10]. Similar to albuminuria, the reflectance data can be used for quantitative analysis [10]. In parallel, the use of sensitive dyes has improved the sensitivity of albuminuria test strips [11].

An interesting recent evolution is the use of smart phones for reading and interpreting urine test strip results [12,13,14]. Mobile healthcare platforms have been proposed, combining a pocket-sized colorimetric reader and commercially available 10-parameter urinalysis paper strips, capable of sending data via a smart phone [15].

In manual microscopy, several steps, such as centrifugation, decantation, and re-suspension, led to cellular lysis and loss [16]. Progress in informatics and computer technology has enabled the development of automated microscopy based on pattern recognition. Over the past two decades, a number of manufacturers have marketed such instruments (Table 1).

In contrast to most other automated urine microscopy analyzers, the iQ200 analyzer (Iris Diagnostics, Chatsworth, CA, USA) uses laminar flow digital imaging technology [17,18,19,20,21]. Its identification software classifies and quantifies the cells and particles in uncentrifuged urine using a single, laminar flow of the specimen through the lens of a charged coupling device video camera. The hundreds of digital camera captures are evaluated by identification software, and each particle is classified based on characteristics, such as shape, contrast, and texture. After classification by the instrument, the operator has the ability to reclassify or correct the obtained images in the correct categories. Various studies have reported a strong correlation between iQ200 output and manual cell counts for RBCs, WBCs, and epithelial cells [17,18,19,20,21]. This correlation coefficient has been 0.894 for RBCs when particle recognition software alone was used and 0.948 for RBCs after re-classification on iQ200 [18]. In the same study, the correlation for WBCs was 0.885 (vs the reference method), which improved to 0.978 following re-classification. The correlation coefficients for iQ200 output following user re-classification were 0.927 for squamous epithelial cells, 0.856 for casts, and 0.706 for non-squamous epithelial cells. iQ200 shows good linearity and precision, and no carry-over has been detected [18,19]. In some cases, falsely elevated RBC counts may occur because of yeast misclassification; that is, yeasts can be confused with RBCs [19]. In addition, the system does not count damaged WBCs and counts fewer RBCs if abnormal RBCs, such as ghosts and dysmorphic cells, are present [22]. Counting results equal or exceed that of routine bright field microscopy or earlier flow cytometric technology. The instrument eliminates manual sample preparation; however, it requires a well-trained technologist for reclassification of findings. The optical system also allows for quantification of urinary bacteria [23]. Owing to the limited ability of the classification software, most problems occur during microorganism analysis [22]. The images of small cocci detected by iQ200 are difficult for the medical technologist to classify as “bacteria.” Better classification results have been obtained for some rod forms [21,24]. In addition, detection of malignant/atypical urothelial cells, which may indicate bladder carcinoma diagnosis, has been achieved using automated intelligent microscopy on iQ200 with a sensitivity of identification of 87.5% [25].

FUS-100 (Dirui, Changchun, China) is a similar analyzer. Yüksel et al. [26] determined that the sensitivity of the FUS-100 for RBCs and WBCs is 73% and 68%, respectively; however, the related FUS-200 analyzer (Dirui) has been found to have unsatisfactory analytical sensitivity for bacteria recognition and quantification [27].

sediMAX (77 Elektronika, Budapest, Hungary) is an automated microscopy image-based urine sediment analyzer (which in some countries is also known as Urised). While iQ200 divides the identified particles in in different categories (RBCs and WBCs) [28], sediMAX shows the particles within whole fields of view, similar to microscopic fields seen with manual microscopy [29]. The instrument provides both bright field and phase-contrast images and generates a composite image out of the bright-field and phase-contrast microscopy images to exhibit the features of each image in one view. Its diagnostic performance with respect to visual phase-contrast microscopy has been evaluated [30]. Within-run imprecision was 17.8% and 6.7% at a concentration of 18×106/L and 447×106/L, respectively, for RBCs and 17% and 4.4% at a concentration of 4×106/L and 258×106/L, respectively, for WBCs. The between-run imprecision was 14.7% at a concentration of 30×106/L and 7.2% at a concentration of 283×106/L for RBCs and 5.4% at a concentration of 25×106/L and 3% at 166×106/L for WBCs. The area under the ROC curve (AUC) ranged from 80% to 90% for RBCs, WBCs, squamous epithelial cells, yeasts, and calcium-oxalate crystals. For non-squamous epithelial cells and pathological and hyaline casts, the AUC ranged from 73% to 74%; no carry-over was detected. Thus, sediMAX is well able to count and identify RBCs, WBCs, squamous epithelial cells, yeasts, bacteria, and calcium-oxalate crystals. Recognition of pathological casts and non-squamous epithelial cells is adequate but needs to be improved.

The second generation sediMAX analyzer (sediMAX 2, 77 Elektronika) allows distinction between four types of crystals: calcium oxalate dihydrate, calcium oxalate monohydrate, uric acid, and struvite. sediMAX conTRUST (77 Elektronika), which is the sediMAX 2 analyzer updated with phase-contrast microscopy, can detect other crystals as well; however, it is not able to identify them precisely, leading the software to classify them as unidentified crystals. The distinction between urine crystals using sediMAX conTRUST is specific but lacks sensitivity [31]. In addition, the system is suitable for parasite recognition [32].

The automated analyzers Cobas u701 (Roche Diagnostics, Mannheim, Germany) [33,34] and Atellica 1500 (Siemens Healthineers, Eschborn, Germany) have been recently introduced in the market [35]. These analyzers are based on similar pattern recognition principles.

Urine particle flow cytometers (UFCs) have improved count precision and accuracy compared with visual microscopy and offer significant labor reduction. The first such UFC, the UF-100 (Sysmex, Kobe, Japan), could identify RBCs, WBCs, squamous epithelial cells, transitional epithelial and renal tubular cells, bacteria, hyaline and inclusional casts, yeast-like cells, crystals, and spermatozoa, using argon laser flow cytometry. Analytic and diagnostic evaluations have demonstrated acceptable linearity over clinically useful working ranges, with an imprecision that is consistently and significantly less than that of microscopy and with negligible carry-over. Studies have compared UFCs with chamber counts, quantitative urine microscopy, sediment counts, test strips, bacterial culture, and urine density [36,37,38]. Clinical studies using UFCs have focused on diagnosis and monitoring of urinary tract infection; localization of the sites of hematuria; and diagnosis, monitoring, and exclusion of renal disease [36].

The classical argon lasers in UFCs have been replaced by semiconductor lasers, which have a much longer lifetime and hence are more economical. The introduction of semiconductor lasers (operating at another blue wavelength) has forced developers to completely redesign the system and adapt the dyes. The newer UF-5000 and UF-4000 (Sysmex) analyzers are able to recognize, count, and classify cells by analyzing forward scatter light (FSC), side scatter light (SSL), side fluorescent light (SFL), and depolarized side scattered light (DSS). DSS was introduced to improve crystal sensitivity and to better discriminate between RBCs and crystals [39]; however, in contrast to microscopy-based readers, differentiation of crystals is not possible.

The most popular approach is to combine test strips with UFCs for primary screening either using both methods (i.e., UFC and strips) or by utilizing the test strips for analytes unrelated to the UFC-analyzed particles. As mechanical coupling of UFCs and test strip readers has been realized [40], expert systems now exist combining both test modalities based on user-definable decision rules. The implementation of such a strategy significantly reduces microscopy review and saves time and cost without diminishing clinical utility.

With UF-1000i (Sysmex), bacteria forward scatter (B_FSC) and fluorescent light scatter (B_FLH) can be used for preliminary discrimination of urinary tract infections (UTIs) caused by gram-positive or gram-negative bacteria [41]. Evaluation of B_FSC and B_FLH parameters from bacteria histograms seems to be useful in distinguishing between gram-negative and gram-positive bacterial strains [42]. B_FSC data could be useful in presumptive exclusion of UTIs caused by gram-positive bacteria [41].

Urinary flow cytometry and UTIs

Urine culture is considered the gold standard for UTI diagnosis. It can determine the level of bacteriuria and antimicrobial susceptibility. However, there is no standardized bacterial count indicating significant bacteriuria, applicable for all types of UTIs. Scientific evidence supporting current urine culture guidelines is often incomplete, and in some cases, the guidelines do not indicate a clear choice [43].

Because of the high percentage of negative results (up to 60% depending on the setting [44,45]), there is a need for an efficient screening method, reducing the number of unnecessary culture tests. Several methods for screening-out culture-negative samples have been developed, including dipstick chemical tests (nitrite, leukocyte esterase, urinary protein, and urinary hemoglobin) and manual or automatic microscopic examination of urine sediment (detection of particles, WBCs, and microorganisms). Although these screening methods are primarily used in general practice and microbiology laboratories, they are subjective and time-consuming and demonstrate poor sensitivity and negative predictive value [46].

Many authors have reported using flow cytometry to detect bacteria and WBCs in urinary samples. Flow cytometry can reduce the number of samples cultured, with a substantial decrease in workload, time, and costs, especially in clinical laboratories [46,47,48]. Using flow cytometry, negative results could be reported earlier, substantially reducing unnecessary empirical antibiotic prescriptions. The use of flow cytometry can reduce the number of urinary samples processed in the clinical laboratory by 28–60% [41,42,44,49,50,51,52,53,54,55,56]. However, there is a wide variation in the applied cut-offs, as well as in the sensitivity and specificity of the obtained results in the literature. These variations are mainly owing to the spectrum of clinical conditions of the patient populations enrolled in these different studies. These differences can be attributed to the different definitions used to classify UTIs, which depend on the guidelines applied in a specific setting. Therefore, we conclude that the applicability of flow cytometry to screen for negative urine samples strongly depends on population characteristics and the definition of a negative urine culture [44]. In addition, a limitation of automated urine analyzers compared with culture is that they count both live and dead bacterial particles, yielding higher particle counts [57].

Integrated urinalysis

To streamline the laboratory workflow, automated test strip readers and particle analyzers have been successfully mechanically integrated. In addition to mechanical integration, the development of expert systems has enabled the comparison and identification of cases that need manual review, which improves the quality of the test results [36].

Because assay imprecision can increase considerably over time, correcting urinary dilution has become increasingly necessary. As hydration is a major pre-analytical confounder in urinalysis, many reference parameters have been introduced to assess urinary dilution and hydration. The most commonly used reference analytes are specific gravity, conductivity, and urinary creatinine determinations [58,59,60]. Conductivity measurement has been integrated in flow cytometry instruments. Specific gravity can be measured using either refractometry or test strips. Table 2 summarizes the most important dilution parameters used in automated urinalysis.

MALDI-TOF mass spectrometry (MS) has been recently introduced in routine clinical microbiology laboratories. As the time needed for culture continues to hinder decision-making and the laboratory workflow, direct-from-sample characterization of the bacterial load constitutes a major advance. Several studies have explored direct analysis of urine samples using MALDI-TOF MS, thereby eliminating the time lag needed for pathogen identification [61,62,63,64,65,66,67,68]. This technique has been suggested as a fast and reliable method for bacterial identification [69].

Initial studies combining urinary tract screening methods with direct application of MALDI-TOF MS in bacteriuria-positive samples have demonstrated direct pathogen identification sensitivity ranging from 67% to 86% [61,64,70,71]. These results mirror those of similar studies showing successful pathogen identification from pathogen-positive blood cultures [61,72].

It is unclear whether MALDI-TOF MS can meet the demands of UTI diagnosis, given the need for screening to improve the yield of positive samples. For direct analysis of urine, initial sample preparation steps are necessary to remove cellular debris, WBCs, and mucus and to collect bacteria. In its current iteration, analysis of MALDI-TOF MS results is hampered by poly-microbial samples. Up to 77% of the catheter-associated UTIs are poly-microbial; therefore, improved algorithms for interpreting the spectra of bacterial combinations are needed for direct-from-urine testing of these samples [73,74]. Additionally, the technique does not provide reliable information on antimicrobial susceptibility for frequently used antibiotics in UTI treatment [75]. Indirect approaches for antimicrobial susceptibility testing are under development and include the measurement of bacterial metabolic by-products in the presence of antibiotics to assess susceptibility.

Oviaño et al. [76] developed an automated MALDI-TOF MS-based assay for rapid, direct detection of carbapenemase-producing Enterobacteriaceae in clinical urine samples within 90 min of sample reception; carbapenemase activity is detected by MALDI-TOF MS analysis following reliable direct identification of gram-negative bacilli. In their study, bacteria were extracted from urine samples, carbapenem resistance was detected using imipenem as an antibiotic marker, and the results were automatically interpreted. Their assay yielded direct reliable identification in 91% of the samples and showed 100% sensitivity and specificity for detecting carbapenemase activity within 90 min of sample reception.

In view of the great need for the development of portable and cost-effective readers, pocket-sized colorimetric readers can be combined with dipsticks in a device that is able to transmit digital information via a smart phone, offering an integrated solution for detecting disease in areas with limited access to trained experts [77]. Advances in microfluidics have enabled the development of new chip-based assays, which will alter the field of automated urinalysis in the near future [78]. Alongside conventional urinalysis applications [79], integrated microfluidic chips have been described as a promising tool for measuring the concentration of bladder cancer cells in urine samples [80]. Similarly, microfluidic paper analytical devices have been designed and fabricated for evaluating bacteria known to cause UTIs (Escherichia coli) and sexually transmitted diseases (Neisseria gonorrhoeae) in human urine samples [81].

Over the past two decades, automated urinalysis has undergone remarkable technical progress. Both microscopy- and flow cytometric-based instruments generate reliable results that are clinically useful, and automated test strip reading provides added value. Additional integration of existing technologies may further reduce turn-around times.

In the meantime, the consolidation of laboratories has led to a reduction in the number of laboratories and has thereby increased the physical distance between patient and laboratory; this trend creates a major pre-analytical challenge. Despite improvements in standardization [82], most of errors in urinalysis occurs outside of the analytical phase; pre-analytical steps, in particular, are much more vulnerable [83]. As analytical variation has been greatly reduced, more efforts need to be focused on the pre-analytical phase.

Current automated urine analyzers
CharacteristicAutomated microscopyFlow cytometry
Sample volume2 mL (Cobas u701)2 mL (UF-5000) (0.6 mL in STAT mode)
2 mL (SediMAX)
2.6 mL (Atellica 1500)
3 mL (FUS-100 and FUS-200)
3 mL (iQ200)
OutputReviewed digital images (sediMAX, FUS-100, FUS-200, Cobas u701, Atellica 1500)Scattergrams (UF-100, UF-500/1000i and UF-4000/5000)
Laminar flow digital imaging (iQ200)
Urinary crystal differentiationPossibleNot possible
Bacterial classificationNot possiblePossible
Throughput (samples/hr)60 (FUS-100)105 (UF-5000)
100 (iQ200)
106 (Atellica 1500)
116 (Cobas u701)
120 (SediMAX conTRUST)
120 (FUS-200)
Integration with urine test strip readerPossiblePossible
ReagentsNot requiredMethylamines (UF-1000i and UF-5000)

Currently used urinary dilution parameters in automated urinalysis
ParameterMeasuresRemarks
Urinary creatinineCreatinine concentration in urineCreatinine output is partially determined by relative muscle mass
Specific gravitySum of charged and uncharged particles in a urinary sampleFalse positive results in the presence of iodinated contrast agents
Specific gravity (refractory index)Sum of charged and uncharged particles in a urinary sampleFalse positive in the presence of contrast agents
Urinary conductivitySum of charged particles dissolved in urineNot sensitive for urinary glucose concentration
OsmolalitySum of charged and uncharged particles in a urinary sampleMay be estimated based on conductivity in flow cytometers (UF-5000)

  1. Hannemann-Pohl K. Automation of urine sediment examination: a comparison of the Sysmex UF-100 automated flow cytometer with routine manual diagnosis (microscopy, test strips, and bacterial culture). Clin Chem Lab Med 1999;37;753-764.
    Pubmed
  2. Fogazzi GB, Garigali G. The different ways to obtain digital images of urine microscopy findings: their advantages and limitations. Clin Chim Acta 2017;466;160-161.
    Pubmed
  3. Langlois MR, Delanghe JR, Steyaert SR, Everaert KC, De Buyzere ML. Automated flow cytometry compared with an automated dipstick reader for urinalysis. Clin Chem 1999;45;118-122.
    Pubmed
  4. Penders J, Fiers T, Delanghe JR. Quantitative evaluation of urinalysis test strips. Clin Chem 2002;48;2236-2241.
    Pubmed
  5. Kubelka P, Ein Beitrag zur Optik der Farbanstriche MF. A contribution to the optics of paints. Z Tech Phys 1931;12;593-601.
  6. Penders J, Fiers T, Giri M, Wuyts B, Ysewyn L, Delanghe JR. Quantitative measurement of ketone bodies in urine using reflectometry. Clin Chem Lab Med 2005;43;724-729.
    Pubmed
  7. Decavele AS, Fiers T, Penders J, Delanghe JR. A sensitive quantitative test strip based point-of-care albuminuria screening assay. Clin Chem Lab Med 2012;50;673-678.
    Pubmed
  8. Delanghe JR, Himpe J, De Cock N, Delanghe S, De Herde K, Stove V, et al. Sensitive albuminuria analysis using dye-binding based test strips. Clin Chim Acta 2017;471;107-112.
    Pubmed
  9. Guy M, Newall R, Borzomato J, Kalra PA, Price C. Diagnostic accuracy of the urinary albumin: creatinine ratio determined by the CLINITEK Microalbumin and DCA 2000+ for the rule-out of albuminuria in chronic kidney disease. Clin Chim Acta 2009;399;54-58.
    Pubmed
  10. Oyaert MN, Himpe J, Speeckaert MM, Stove VV, Delanghe JR. Quantitative urine test strip reading for leukocyte esterase and hemoglobin peroxidase. Clin Chem Lab Med 2018;56;1126-1132.
    Pubmed
  11. Urit 14F urine reagent strips. Package insert: Urit medical Electronic Co., Ltd., Guangxi 51004. PRACTICE China
  12. Smith GT, Dwork N, Khan SA, Millet M, Magar K, Javanmard M, et al. Robust dipstick urinalysis using a low-cost, micro-volume slipping manifold and mobile phone platform. Lab Chip 2016;16;2069-2078.
    Pubmed
  13. Lee DS, Jeon BG, Ihm C, Park JK, Jung MY. A simple and smart telemedicine device for developing regions: a pocket-sized colorimetric reader. Lab Chip 2011;11;120-126.
    Pubmed
  14. Mohammadi S, Maeki M, Mohamadi RM, Ishida A, Tani H, Tokeshi M. An instrument-free, screen-printed paper microfluidic device that enables bio and chemical sensing. Analyst 2015;140;6493-6499.
    Pubmed
  15. Ginardi RVH, Saikhu A. In: Linawati MMS. Information and communication technology. ICT-EurAsia 2014. Lecture notes in computer science, vol. 8407. Berlin, Heidelberg: Springer; 2014. p. 66-77.
  16. İnce FD, Ellidağ HY, Koseoğlu M, Şimşek N, Yalçın H, Zengin MO. The comparison of automated urine analyzers with manual microscopic examination for urinalysis automated urine analyzers and manual urinalysis. Pract Lab Med 2016;5;14-20.
    Pubmed
  17. Chien TI, Kao JT, Liu HL, Lin PC, Hong JS, Hsieh HP, et al. Urine sediment examination: a comparison of automated urinalysis systems and manual microscopy. Clin Chim Acta 2007;384;28-34.
    Pubmed
  18. Linko S, Kouri TT, Toivonen E, Ranta PH, Chapoulaud E, Lalla M. Analytical performance of the Iris iQ200 automated urine microscopy analyzer. Clin Chim Acta 2006;372;54-64.
    Pubmed
  19. Wah DT, Wises PK, Butch AW. Analytic performance of the iQ200 automated urine microscopy analyzer and comparison with manual counts using Fuchs-Rosenthal cell chambers. Am J Clin Pathol 2005;123;290-296.
    Pubmed
  20. Park J, Kim J. Evaluation of iQ200 automated urine microscopy analyzer. Korean J Lab Med 2008;28;267-273.
    Pubmed
  21. Budak YU, Huysal K. Comparison of three automated systems for urine chemistry and sediment analysis in routine laboratory practice. Clin Lab 2011;57;47-52.
    Pubmed
  22. Shayanfar N, Tobler U, von Eckardstein A, Bestmann L. Automated urinalysis: first experiences and a comparison between the Iris iQ200 urine microscopy system, the Sysmex UF-100 flow cytometer and manual microscopic particle counting. Clin Chem Lab Med 2007;45;1251-1256.
    Pubmed
  23. Stürenburg E, Kramer J, Schön G, Cachovan G, Sobottka I. Detection of significant bacteriuria by use of the iQ200 automated urine microscope. J Clin Microbiol 2014;52;2855-2860.
    Pubmed
  24. Lamchiagdhase P, Preechaborisutkul K, Lomsomboon P, Srisuchart P, Tantiniti P, Khan-u-Ra N, et al. Urine sediment examination: a comparison between the manual method and the iQ200 automated urine microscopy analyzer. Clin Chim Acta 2005;358;167-174.
    Pubmed
  25. Anderlini R, Manieri G, Lucchi C, Raisi O, Soliera AR, Torricelli F, et al. Automated urinalysis with expert review for incidental identification of atypical urothelial cells: an anticipated bladder carcinoma diagnosis. Clin Chim Acta 2015;451;252-256.
    Pubmed
  26. Yüksel H, Kiliç E, Ekinci A, Evliyaoğlu O. Comparison of fully automated urine sediment analyzers H800-FUS100 and LabUMat-UriSed with manual microscopy. J Clin Lab Anal 2013;27;312-316.
    Pubmed
  27. Kocer D, Sarıguzel FM, Karakukcu C. Cutoff values for bacteria and leukocytes for urine sediment analyzer FUS200 in culture-positive urinary-tract infections. Scand J Clin Lab Invest 2014;74;414-417.
    Pubmed
  28. Dewulf G, Harrois D, Mazars E, Cattoen C, Canis F. Evaluation of the performances of the iQ(&reg)200 ELITE automated urine microscopy analyser and comparison with manual microscopy method. Pathol Biol (Paris) 2011;59;264-268.
    Pubmed
  29. Akın OK, Serdar MA, Cizmeci Z, Genc O, Aydin S. Comparison of LabUMat-with-urised and iQ200 fully automatic urine sediment analysers with manual urine analysis. Biotechnol Appl Biochem 2009;53;139-144.
    Pubmed
  30. Zaman Z, Fogazzi GB, Garigali G, Croci MD, Bayer G, Kránicz T. Urine sediment analysis: analytical and diagnostic performance of sediMAX – a new automated microscopy image-based urine sediment analyser. Clin Chim Acta 2010;411;147-154.
    Pubmed
  31. Castiglione V, Cavalier E, Diop C, Gadisseur R. Distinction between urine crystals by automated urine analyzer SediMAX conTRUST is specific but lacks sensitivity. Clin Chem Lab Med 2017;55;e288-e290.
    Pubmed
  32. Intra J, Sala MR, Falbo R, Cappellini F, Brambilla P. Improvement in the detection of enteric protozoa from clinical stool samples using the automated urine sediment analyzer sediMAX&reg 2 compared to sediMAX&reg 1. Eur J Clin Microbiol Infect Dis 2017;36;147-151.
    Pubmed
  33. Lee W, Ha JS, Ryoo NH. Comparison of the automated cobas u 701 urine microscopy and UF-1000i flow cytometry systems and manual microscopy in the examination of urine sediments. J Clin Lab Anal 2016;30;663-671.
    Pubmed
  34. Wesarachkitti B, Khejonnit V, Pratumvinit B, Reesukumal K, Meepanya S, Pattanavin C, et al. Performance evaluation and comparison of the fully automated urinalysis analyzers UX-2000 and Cobas. Lab Med 2016;47;124-133.
    Pubmed
  35. Bakan E, Ozturk N, Baygutalp NK, Polat E, Akpinar K, Dorman E, et al. Comparison of Cobas 6500 and Iris IQ200 fully-automated urine analyzers to manual urine microscopy. Biochem Med (Zagreb) 2016;26;365-375.
    Pubmed
  36. Delanghe JR, Kouri TT, Huber AR, Hannemann-Pohl K, Guder WG, Lun A, et al. The role of automated urine particle flow cytometry in clinical practice. Clin Chim Acta 2000;301;1-18.
    Pubmed
  37. Manoni F, Tinello A, Fornasiero L, Hoffer P, Temporin V, Valverde S, et al. Urine particle evaluation: a comparison between the UF-1000i and quantitative microscopy. Clin Chem Lab Med 2010;48;1107-1111.
    Pubmed
  38. Jiang T, Chen P, Ouyang J, Zhang S, Cai D. Urine particles analysis: performance evaluation of Sysmex UF-1000i and comparison among urine flow cytometer, dipstick, and visual microscopic examination. Scand J Clin Lab Invest 2011;71;30-37.
    Pubmed
  39. Previtali G, Ravasio R, Seghezzi M, Buoro S, Alessio MG. Performance evaluation of the new fully automated urine particle analyser UF-5000 compared to the reference method of the Fuchs-Rosenthal chamber. Clin Chim Acta 2017;472;123-130.
    Pubmed
  40. Sánchez-Mora C, Acevedo D, Porres MA, Chaqués AM, Zapardiel J, Gallego-Cabrera A, et al. Comparison of automated devices UX-2000 and SediMAX/AutionMax for urine samples screening: a multicenter Spanish study. Clin Biochem 2017;50;714-718.
    Pubmed
  41. Gessoni G, Saccani G, Valverde S, Manoni F, Caputo M. Does flow cytometry have a role in preliminary differentiation between urinary tract infections sustained by gram positive and gram negative bacteria? An Italian polycentric study. Clin Chim Acta 2015;440;152-156.
    Pubmed
  42. De Rosa R, Grosso S, Bruschetta G, Avolio M, Stano P, Modolo ML, et al. Evaluation of the Sysmex UF1000i flow cytometer for ruling out bacterial urinary tract infection. Clin Chim Acta 2010;411;1137-1142.
    Pubmed
  43. Oyaert M, Van Meensel B, Cartuyvels R, Frans J, Laffut W, Vandecandelaere P, et al. Laboratory diagnosis of urinary tract infections: towards a BILULU consensus guideline. J Microbiol Methods 2018;146;92-99.
    Pubmed
  44. Broeren MA, Bahçeci S, Vader HL, Arents NL. Screening for urinary tract infection with the Sysmex UF-1000i urine flow cytometer. J Clin Microbiol 2011;49;1025-1029.
    Pubmed
  45. Jolkkonen S, Paattiniemi EL, Kärpänoja P, Sarkkinen H. Screening of urine samples by flow cytometry reduces the need for culture. J Clin Microbiol 2010;48;3117-3121.
    Pubmed
  46. Mejuto P, Luengo M, Díaz-Gigante J. Automated flow cytometry: an alternative to urine culture in a routine clinical microbiology laboratory?. Int J Microbiol 2017;2017:8532736.
    Pubmed
  47. Yusuf E, Van Herendael B, van Schaeren J. Performance of urinalysis tests and their ability in predicting results of urine cultures: a comparison between automated test strip analyser and flow cytometry in various subpopulations and types of samples. J Clin Pathol 2017;70;631-636.
    Pubmed
  48. Monsen T, Ryden P. A new concept and a comprehensive evaluation of SYSMEX UF-1000i flow cytometer to identify culture-negative urine specimens in patients with UTI. Eur J Clin Microbiol Infect Dis 2017;36;1691-1703.
    Pubmed
  49. García-Coca M, Gadea I, Esteban J. Relationship between conventional culture and flow cytometry for the diagnosis of urinary tract infection. J Microbiol Methods 2017;137;14-18.
    Pubmed
  50. Íñigo M, Coello A, Fernández-Rivas G, Carrasco M, Marcó C, Fernández A, et al. Evaluation of the SediMax automated microscopy sediment analyzer and the Sysmex UF-1000i flow cytometer as screening tools to rule out negative urinary tract infections. Clin Chim Acta 2016;456;31-35.
    Pubmed
  51. Martín-Gutiérrez G, Porras-González A, Martín-Pérez C, Lepe JA, Aznar J. Evaluation and optimization of the Sysmex UF1000i system for the screening of urinary tract infection in primary health care elderly patients. Enferm Infecc Microbiol Clin 2015;33;320-323.
    Pubmed
  52. Gutiérrez-Fernández J, Lara A, Bautista MF, de Dios Luna J, Polo P, Miranda C, et al. Performance of the Sysmex UF1000i system in screening for significant bacteriuria before quantitative culture of aerobic/facultative fast-growth bacteria in a reference hospital. J Appl Microbiol 2012;113;609-614.
    Pubmed
  53. Kadkhoda K, Manickam K, Degagne P, Sokolowski P, Pang P, Kontzie N, et al. UF-1000i flow cytometry is an effective screening method for urine specimens. Diagn Microbiol Infect Dis 2011;69;130-136.
    Pubmed
  54. Pieretti B, Brunati P, Pini B, Colzani C, Congedo P, Rocchi M, et al. Diagnosis of bacteriuria and leukocyturia by automated flow cytometry compared with urine culture. J Clin Microbiol 2010;48;3990-3996.
    Pubmed
  55. van der Zwet WC, Hessels J, Canbolat F, Deckers MM. Evaluation of the Sysmex UF-1000i&reg urine flow cytometer in the diagnostic work-up of suspected urinary tract infection in a Dutch general hospital. Clin Chem Lab Med 2010;48;1765-1771.
    Pubmed
  56. Krongvorakul J, Phundhusuwannakul S, Santanirand P, Kunakorn M. A flow cytometric urine analyzer for bacteria and white blood cell counts plus urine dispstick test for rapid screening of bacterial urinary tract infection. Asian Biomed 2012;6;601-608.
  57. Poropatich CO, Mendoza SM, Hitlan JJ, Wilkinson DS. Inconsistent detection of bacteriuria with the Yellow IRIS automated urinalysis workstation. Lab Med 1988;19;499-501.
  58. McCrossin T, Roy LP. Comparison of hydrometry, refractometry, osmometry and Ames N-Multistix SG in estimation of urinary concentration. Aust Paediatr J 1985;21;185-188.
    Pubmed
  59. Brandon CA. Urine specific gravity measurement: reagent strip versus refractometer. Clin Lab Sci 1994;7;308-310.
    Pubmed
  60. Dorizzi RM, Caputo M. Measurement of urine relative density using refractometer and reagent strips. Clin Chem Lab Med 1998;36;925-928.
    Pubmed
  61. Íñigo M, Coello A, Fernández-Rivas G, Rivaya B, Hidalgo J, Quesada MD, et al. Direct identification of urinary tract pathogens from urine samples, combining urine screening methods and matrix-assisted laser desorption ionization-time of flight mass spectrometry. J Clin Microbiol 2016;54;988-993.
    Pubmed
  62. Zboromyrska Y, Rubio E, Alejo I, Vergara A, Mons A, Campo I, et al. Development of a new protocol for rapid bacterial identification and susceptibility testing directly from urine samples. Clin Microbiol Infect 2016;22;561.e1-561.e6.
  63. Veron L, Mailler S, Girard V, Muller BH, L'Hostis G, Ducruix C, et al. Rapid urine preparation prior to identification of uropathogens by MALDI-TOF MS. Eur J Clin Microbiol Infect Dis 2015;34;1787-1795.
    Pubmed
  64. Ferreira L, Sánchez-Juanes F, González-Avila M, Cembrero-Fuciños D, Herrero-Hernández A, González-Buitrago JM, et al. Direct identification of urinary tract pathogens from urine samples by matrix-assisted laser desorption ionization-time of flight mass spectrometry. J Clin Microbiol 2010;48;2110-2115.
    Pubmed
  65. Stevenson LG, Drake SK, Shea YR, Zelazny AM, Murray PR. Evaluation of matrix-assisted laser desorption ionization-time of flight mass spectrometry for identification of clinically important yeast species. J Clin Microbiol 2010;48;3482-3486.
    Pubmed
  66. Wang XH, Zhang G, Fan YY, Yang X, Sui WJ, Lu XX. Direct identification of bacteria causing urinary tract infections by combining matrix-assisted laser desorption ionization-time of flight mass spectrometry with UF-1000i urine flow cytometry. J Microbiol Methods 2013;92;231-235.
    Pubmed
  67. March Rosselló GA, Gutiérrez Rodríguez MP, de Lejarazu Leonardo RO, Orduña Domingo A, Bratos Pérez MA. Procedure for microbial identification based on matrix-assisted laser desorption/ionization-time of flight mass spectrometry from screening-positive urine samples. APMIS 2014;122;790-795.
    Pubmed
  68. Demarco ML, Burnham CA. Diafiltration MALDI-TOF mass spectrometry method for culture-independent detection and identification of pathogens directly from urine specimens. Am J Clin Pathol 2014;141;204-212.
    Pubmed
  69. Seng P, Drancourt M, Gouriet F, La Scola B, Fournier PE, Rolain JM, et al. Ongoing revolution in bacteriology: routine identification of bacteria by matrix-assisted laser desorption ionization time-of-flight mass spectrometry. Clin Infect Dis 2009;49;543-551.
    Pubmed
  70. Burillo A, Rodríguez-Sánchez B, Ramiro A, Cercenado E, Rodríguez-Créixems M, Bouza E. Gram-stain plus MALDI-TOF MS (matrix-assisted laser desorption ionization-time of flight mass spectrometry) for a rapid diagnosis of urinary tract infection. PLoS One 2014;9:e86915.
    Pubmed
  71. Köhling HL, Bittner A, Müller KD, Buer J, Becker M, Rübben H, et al. Direct identification of bacteria in urine samples by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry and relevance of defensins as interfering factors. J Med Microbiol 2012;61;339-344.
    Pubmed
  72. Singhal N, Kumar M, Kanaujia PK, Virdi JS. MALDI-TOF mass spectrometry: an emerging technology for microbial identification and diagnosis. Front Microbiol 2015;6:791.
    Pubmed
  73. Kline KA, Lewis AL. Gram-positive uropathogens, polymicrobial urinary tract infection, and the emerging microbiota of the urinary tract. Microbiol Spectr 2016;4.
  74. Siegman-Igra Y. The significance of urine culture with mixed flora. Curr Opin Nephrol Hypertens 1994;3;656-659.
    Pubmed
  75. Jung JS, Eberl T, Sparbier K, Lange C, Kostrzewa M, Schubert S, et al. Rapid detection of antibiotic resistance based on mass spectrometry and stable isotopes. Eur J Clin Microbiol Infect Dis 2014;33;949-955.
    Pubmed
  76. Oviaño M, Ramírez CL, Barbeyto LP, Bou G. Rapid direct detection of carbapenemase-producing Enterobacteriaceae in clinical urine samples by MALDI-TOF MS analysis. J Antimicrob Chemother 2017;72;1350-1354.
    Pubmed
  77. Lee DS, Jeon BG, Ihm C, Park JK, Jung MY. A simple and smart telemedicine device for developing regions: a pocket-sized colorimetric reader. Lab Chip 2011;11;120-126.
    Pubmed
  78. Yetisen AK, Akram MS, Lowe CR. Paper-based microfluidic point-of-care diagnostic devices. Lab Chip 2013;13;2210-2251.
    Pubmed
  79. Jalal UM, Jin GJ, Shim JS. Paper-plastic hybrid microfluidic device for smartphone-based colorimetric analysis of urine. Anal Chem 2017;89;13160-13166.
    Pubmed
  80. Hosseini SA, Zanganeh S, Akbarnejad E, Salehi F, Abdolahad M. Microfluidic device for label-free quantitation and distinction of bladder cancer cells from the blood cells using micro machined silicon based electrical approach; suitable in urinalysis assays. J Pharm Biomed Anal 2017;134;36-42.
    Pubmed
  81. Cho S, Park TS, Nahapetian TG, Yoon JY. Smartphone-based, sensitive μPAD detection of urinary tract infection and gonorrhea. Biosens Bioelectron 2015;74;601-611.
    Pubmed
  82. Kouri TT, Gant VA, Fogazzi GB, Hofmann W, Hallander HO, Guder WG. Towards European urinalysis guidelines. Introduction of a project under European Confederation of Laboratory Medicine. Clin Chim Acta 2000;297;305-311.
    Pubmed
  83. Delanghe JR, Speeckaert MM. Preanalytics in urinalysis. Clin Biochem 2016;49;1346-1350.
    Pubmed